Disposable Vape Aus0

What is in a vape

A plain guide to vape ingredients: what is in e-liquid (propylene glycol, vegetable glycerin and nicotine) and to the by-products that can form in the aerosol when a device runs too hot. In Australia, the quality of these ingredients is covered by the TGA standard known as TGO 110.

Base ingredients

Vape ingredients: what e-liquid is made of

Almost every e-liquid, in a disposable or a pod, is a mix of the same three things plus flavourings. Here is what each one does.

Definition

Propylene glycol (propane-1,2-diol) is a colourless, low-viscosity synthetic liquid. It is hygroscopic and miscible with water, and it dissolves flavour compounds and nicotine well, which is why it serves as the main flavour carrier in e-liquid.

It vaporises at a lower temperature than glycerin and produces a thinner aerosol with a stronger throat sensation. Outside vaping, it is used in pharmaceutical, food and cosmetic formulations.

QualityPharmaceutical-grade PG is tested for water content, heavy metals and related glycols. TGO 110 sets the quality rules for vape ingredients in Australia.
IUPAC name
Propane-1,2-diol
CAS number
57-55-6
Formula
C3H8O2
Molar mass
76.09 g/mol
Boiling point
188.2 °C
IARC
Not classified
Key thermal products
Formaldehyde, acetaldehyde

Definition

Vegetable glycerin is glycerol (propane-1,2,3-triol) derived from plant oils. It is a clear, viscous, slightly sweet liquid with a higher boiling point than propylene glycol.

Its viscosity and boiling point produce a denser visible aerosol and a smoother draw. The VG/PG ratio, often printed on the label as 50/50 or 70/30, sets the balance between aerosol volume and flavour carry.

Quality Pharmacopoeia-style limits cover diethylene glycol and ethylene glycol. It is one of the two base liquids in almost every e-liquid.
IUPAC name
Propane-1,2,3-triol
CAS number
56-81-5
Formula
C3H8O3
Molar mass
92.09 g/mol
Boiling point
290 °C
IARC
Not classified
Key thermal products
Acrolein, formaldehyde

Definition

Nicotine is an alkaloid extracted from tobacco or produced synthetically. It is addictive and acutely toxic in concentrated form. In e-liquid it appears either as freebase nicotine or as a nicotine salt, where an acid such as benzoic acid lowers the pH and gives a smoother sensation at higher strengths.

"Pharmaceutical grade" means it meets a pharmacopoeia monograph, which sets an assay range for nicotine content and limits for related alkaloids such as nornicotine, anatabine and myosmine.

StrengthNicotine strength is shown on the box, usually as a percentage or in mg/mL. Nicotine is addictive, and e-liquid is poisonous if swallowed, so keep devices away from children and pets.
IUPAC name
3-[(2S)-1-Methylpyrrolidin-2-yl]pyridine
CAS number
54-11-5
Formula
C10H14N2
Molar mass
162.23 g/mol
Boiling point
247 °C
IARC
Not classified
Forms
Freebase or nicotine salt

Aerosol parameter

Where base ingredients vaporise, and where they degrade

Boiling points of the three base ingredients against coil temperatures reported in laboratory studies. Yields of aldehydes rise sharply in dry-puff conditions, when the wick runs low and the coil overheats. That burnt taste is the sign to stop and swap the pod or coil.

0 °C100200300400 °C

Operating and dry-puff ranges are approximate values reported in the literature and vary by device, power setting and wick saturation.

In the aerosol

What can form when it runs hot

These are not ingredients. They are by-products that studies have found in vape aerosol, mostly when a device overheats or a coil is worn out. Knowing about them is the best reason to replace coils on time and avoid dry hits.

Chemical overview

Formaldehyde is the simplest aldehyde. In e-cigarette aerosol it forms when propylene glycol and glycerol undergo thermal oxidation at high coil temperatures. Some studies have also reported formaldehyde-releasing hemiacetals, which form when formaldehyde reacts with PG or glycerol in the aerosol.

Laboratory studies report low yields under normal operating conditions and sharply higher yields under dry-puff conditions.

How it is measuredLabs measure formaldehyde by DNPH derivatisation and HPLC under standard puffing settings.
IUPAC name
Methanal
CAS number
50-00-0
Formula
CH2O
Molar mass
30.03 g/mol
Boiling point
−19 °C
IARC
Group 1
Precursors
PG, glycerol

Chemical overview

Acetaldehyde is a two-carbon aldehyde that forms mainly when propylene glycol degrades at high temperature. It is usually measured alongside formaldehyde, and both increase with coil temperature and power.

How it is measuredMeasured in the same carbonyl panel as formaldehyde (DNPH derivatisation, HPLC) under standardised puffing regimes.
IUPAC name
Ethanal
CAS number
75-07-0
Formula
C2H4O
Molar mass
44.05 g/mol
Boiling point
20.2 °C
IARC
Group 2B
Precursors
Mainly PG

Chemical overview

Acrolein forms when glycerol loses two water molecules at high temperature (dehydration). It is a strong respiratory irritant. Because glycerol is its main precursor, high-VG liquids heated past their normal vaporisation range are the main route to acrolein formation.

How it is measuredMeasured in carbonyl panels using DNPH derivatisation with HPLC, or by other validated methods, under standardised puffing regimes.
IUPAC name
Prop-2-enal
CAS number
107-02-8
Formula
C3H4O
Molar mass
56.06 g/mol
Boiling point
53 °C
IARC
Group 2A
Precursors
Glycerol

Chemical overview

Nickel is a component of nichrome heating wire and of nickel-plated contacts and housings. Laboratory studies of e-cigarette aerosol have reported nickel transfer from these materials into liquid and aerosol, with levels that vary widely between devices.

Variables studied include coil material, coil age and wear, operating temperature, and how long liquid stays in contact with metal parts.

How it is measuredMeasured by inductively coupled plasma mass spectrometry (ICP-MS) on collected aerosol or on e-liquid sampled from the device.
CAS number
7440-02-0
Symbol
Ni
Atomic mass
58.69 g/mol
IARC
Compounds: Group 1 · Metal: Group 2B
Possible sources
Nichrome coils, plated parts

Chemical overview

Chromium is present in the three most common heating-element alloys: nichrome (nickel-chromium), stainless steel and FeCrAl (often sold as Kanthal). Its health significance depends on oxidation state: hexavalent chromium compounds are classified as carcinogenic, while metallic and trivalent chromium are not classifiable.

How it is measuredTotal chromium is measured by ICP-MS. Telling chromium(III) apart from chromium(VI) requires additional speciation analysis, which most aerosol studies do not perform.
CAS number
7440-47-3
Symbol
Cr
Atomic mass
52.00 g/mol
IARC
Cr(VI): Group 1 · Metal/Cr(III): Group 3
Possible sources
Nichrome, stainless steel, FeCrAl

Chemical overview

Lead is not a component of standard heating-wire alloys, but it can be present in solder joints that connect the coil to the battery circuit and in some brass or alloy components. Laboratory studies have reported lead in aerosol and in liquid sampled from some devices.

How it is measuredMeasured by ICP-MS.
CAS number
7439-92-1
Symbol
Pb
Atomic mass
207.2 g/mol
IARC
Inorganic compounds: Group 2A
Possible sources
Solder joints, some alloys

Questions

Ingredients, answered

Mostly propylene glycol (PG) and vegetable glycerin (VG), plus nicotine and flavourings. PG carries the flavour and gives the throat hit; VG makes the vapour thicker and smoother.

TGO 110 is the Therapeutic Goods Administration standard that sets quality and safety rules for nicotine vapes in Australia, including which ingredients are allowed and how products are labelled. You can read the current rules on the TGA vaping hub.

It is the mix of the two base liquids. A higher VG ratio (like 70/30) gives bigger, smoother clouds; a higher PG ratio gives a stronger throat hit and carries flavour better. Most disposables use a balanced mix.

Usually the wick has run dry or the coil is worn out, so the coil overheats. That is also when more aldehydes form. Stop using it and swap the pod or coil, or, for a disposable, it has likely run out.

Nicotine salt has an acid added that lowers the pH, so higher strengths feel smoother. Freebase nicotine is the traditional form and feels harsher at the same strength. Both are addictive.

Sources

  1. Therapeutic Goods Administration (TGA) vaping hub, including TGO 110
  2. IARC Monographs for the classifications named on this page
  3. PubChem for the CAS numbers and physical data
  4. ISO 20768:2018, the standard machine method for testing vape aerosol

About this page

Written by Disposable Vape AUS as a plain-English guide. It is general information, not medical advice. Last checked 19 October 2026. Questions about vape ingredients? Ask us on the live chat.